This page is also available in French. Switch to French

This page is also available in Spanish. Switch to Spanish

EVCommunicationError: what it means and what to do

"Communication failure with the vehicle, might be Mode 3 or other communication protocol problem" (OCPP 1.6, §7.6). It is a warning, not a fault: the charger should go to SuspendedEVSE, not Faulted.

What it means

The specification calls it "not a real error".

It SHALL only be used with the statuses Preparing, SuspendedEV, SuspendedEVSE and Finishing, and be treated as a warning (OCPP 1.6, §7.6, §4.9). A charger that reports it together with Faulted is not following that rule.

The basic link between car and charger is the control pilot: the charger uses the control pilot signal, as defined in IEC 61851-1, to tell the car the maximum current or power it may take (OCPP 1.6, §2.2). The signalling is low-voltage DC and PWM over a control pilot line, per IEC 61851-1 and SAE J1772 (OCPP 2.0.1 Appendices, §3.2.21). ISO 15118 is a newer protocol for the same car-to-charger communication (OCPP 2.0.1 Part 0, §2.5).

OCPP 1.6 renamed the older value Mode3Error to EVCommunicationError (OCPP 1.6, Appendix A.1).

In OCPP 2.0.1

StatusNotification carries no error code in OCPP 2.0.1 (OCPP 2.0.1, §1.59.1).

Look for NotifyEvent on the CPPWMController component, whose Problem variable means "CP PWM controller fault" and whose State variable holds the IEC 61851-1 state, A to E (OCPP 2.0.1 Appendices, §3.2.21).

Chargers that talk to the car over ISO 15118 or CHAdeMO have an ISO15118Ctrlr or CHAdeMOCtrlr component. On both, Problem means a controller fault and Tripped means the session with the car was aborted or ended abnormally (OCPP 2.0.1 Appendices, §3.1.4, §3.1.9). The SuspendedEVSE state lives in the transaction's chargingState (OCPP 2.0.1, §3.16).

Likely causes

OCPP does not list causes.

It says only that communication with the vehicle failed, on Mode 3 or another protocol (OCPP 1.6, §7.6). The checks below help tell a car problem from a charger problem.

First three checks

  • 1.

    One car or many? Group events by vehicle or by idTag.

  • 2.

    One model or many? Group by charger model and firmware version.

  • 3.

    Read the status that came with the code. Faulted means the connector is not available for energy delivery, whatever the code says (OCPP 1.6, §7.7).

What to do

  • Safe remote action

    Usually none: it is a warning (OCPP 1.6, §4.9). The driver can unplug and plug in again, which starts a new session (OCPP 1.6, §4.9).

  • Dispatch when

    Many different cars fail on one connector. Contact the charger manufacturer with the events grouped by vehicle; if the cable or connector looks damaged, drivers should not use it.

  • Do not

    Do not reset a charger because one car's handshake failed.

What to tell the customer

"Your car and the charger couldn't agree how to start charging.

Please unplug and plug in again to start a new session. If it keeps happening with your car, we'll look into it."

A detection rule to start from

Log EVCommunicationError as a warning.

If several different idTags hit it on one connector within a week, open a ticket with the charger manufacturer for that connector. If one idTag hits it on several chargers, open a vehicle-compatibility ticket.

Sources

  1. Open Charge Alliance (2017). Open Charge Point Protocol 1.6, edition 2 (opens in a new tab). §2.2 Definitions (Control Pilot signal), §4.9 Status Notification, §7.6 ChargePointErrorCode, §7.7 ChargePointStatus, Appendix A.1 Updated/New Messages; accessed 2026-10-22.
  2. Open Charge Alliance (2025). OCPP 2.0.1 Edition 4, Part 0 – Introduction (opens in a new tab). §2.5 Support for ISO 15118; accessed 2026-10-22.
  3. Open Charge Alliance (2025). OCPP 2.0.1 Edition 4, Part 2 – Specification (opens in a new tab). §1.59.1 StatusNotificationRequest, §3.16 ChargingStateEnumType; accessed 2026-10-22.
  4. Open Charge Alliance (2025). OCPP 2.0.1 Part 2 – Appendices, v1.5 (opens in a new tab). §3.1.4 CHAdeMOCtrlr, §3.1.9 ISO15118Ctrlr, §3.2.21 CPPWMController; accessed 2026-10-22.

Talk to us about your chargers

What happens next

  1. Tell us about your network.
  2. Meet a Kinethra specialist.
  3. Get your chargers live on Kinethra.
  • 40,000+ chargers onlineOn the Kinethra platform.
  • OCPP 1.6 and 2.0.1Kinethra works with OCPP chargers from any manufacturer.
  • No commission on charging revenueKinethra takes none.
  1. 01Contact
  2. 02Business
  3. 03Request

Step 1 of 3

We use your details to answer your request. See our Privacy Policy for details.