This page is also available in French. Switch to French

This page is also available in Spanish. Switch to Spanish

OCPP connector status, explained

OCPP 1.6 has nine connector statuses. OCPP 2.0.1 has five, and reports what happens during a session as a separate charging state (OCPP 1.6, §7.7; OCPP 2.0.1, §3.23, §3.16).

The nine statuses in OCPP 1.6

  • Available

    Free for a new user. Operative.

  • Preparing

    No longer free, but no transaction yet: a card was presented, a cable plugged in or a car is in the bay. Operative.

  • Charging

    The contactor is closed and the car can charge. Operative.

  • SuspendedEVSE

    The car is plugged in but the charger is not offering energy: a smart charging limit, a local supply limit, or the start of the transaction was not authorized. Operative.

  • SuspendedEV

    The charger offers energy but the car is not taking any. Operative.

  • Finishing

    The transaction has stopped, but the connector is not free yet: the cable is still in or the car is still in the bay. Operative.

  • Reserved

    Reserved with ReserveNow. Operative.

  • Unavailable

    Set by ChangeAvailability, or by the charger itself, for example while it updates firmware. Inoperative.

  • Faulted

    An error was reported and the connector is not available for energy delivery. Inoperative.

SuspendedEV or SuspendedEVSE?

The difference is who is holding back the energy.

With SuspendedEVSE the charger is not offering it; with SuspendedEV the charger offers it and the car does not take it (OCPP 1.6, §7.7). If both hold back at once, SuspendedEVSE takes precedence (OCPP 1.6, §4.9).

A short SuspendedEV or SuspendedEVSE between Preparing and Charging is normal: the specification describes it as part of a session starting, possibly within a couple of seconds (OCPP 1.6, §4.9).

A long SuspendedEV points at the car: charging stops at the car's request, for example when the car opens its S2 switch (OCPP 1.6, §4.9). A long SuspendedEVSE points at the charger side, for example a smart charging restriction or a local supply limit (OCPP 1.6, §7.7). To check smart charging, ask for the composite schedule with GetCompositeSchedule: it is the result of all active charging schedules and possible local limits (OCPP 1.6, §5.7).

When a car is unplugged on its side during a transaction, StopTransactionOnEVSideDisconnect decides what happens. If it is false, the charger reports SuspendedEV with the info "EV side disconnected" and the transaction keeps running. If it is true, it reports Finishing and stops the transaction (OCPP 1.6, §4.9).

Why some statuses never reach you

A charger may skip a status that lasted less than MinimumStatusDuration, and the manufacturer may add its own minimum on top.

Setting MinimumStatusDuration to zero does not remove the manufacturer's delay (OCPP 1.6, §4.9).

Connector 0 means the charger as a whole and only uses Available, Unavailable and Faulted (OCPP 1.6, §7.7).

Unavailable set by ChangeAvailability must survive reboots, so a reset will not bring such a connector back (OCPP 1.6, §4.9).

An error code with a status other than Faulted is a warning: charging is still possible (OCPP 1.6, §4.9).

OCPP 2.0.1: status and charging state

  • Connector status

    Available, Occupied, Reserved, Unavailable and Faulted. Occupied means the connector is not available for a new driver (OCPP 2.0.1, §3.23).

  • Charging state

    TransactionEvent reports the chargingState whenever it changes: Charging, EVConnected, SuspendedEV, SuspendedEVSE or Idle (OCPP 2.0.1, §2.48, §3.16).

  • Why it changed

    In OCPP 2.0.1, StatusNotification only reports connector availability; the transaction-related status reports move to TransactionEvent (OCPP 2.0.1 Part 0, §2.2.1).

Reading 1.6 and 2.0.1 side by side

OCPP 1.6 created Preparing, Charging, SuspendedEV, SuspendedEVSE and Finishing by splitting the older Occupied status (OCPP 1.6, §4.9, Appendix A.1).

OCPP 2.0.1 brings Occupied back for a connector that is not available for a new driver (OCPP 2.0.1, §3.23) and moves the detail into the charging state: Charging, EVConnected, SuspendedEV, SuspendedEVSE or Idle, where Idle means the car and charger are not linked (OCPP 2.0.1, §3.16).

If the protocol between car and charger can detect that a car is plugged in, EVConnected becomes active only once it has detected it (OCPP 2.0.1, §3.16).

Sources

  1. Open Charge Alliance (2017). Open Charge Point Protocol 1.6, edition 2 (opens in a new tab). §4.9 Status Notification, §5.7 Get Composite Schedule, §7.7 ChargePointStatus, Appendix A.1 Updated/New Messages; accessed 2026-10-22.
  2. Open Charge Alliance (2025). OCPP 2.0.1 Edition 4, Part 0 – Introduction (opens in a new tab). §2.2.1 One message for all transaction related functionalities; accessed 2026-10-22.
  3. Open Charge Alliance (2025). OCPP 2.0.1 Edition 4, Part 2 – Specification (opens in a new tab). §2.48 TransactionType, §3.16 ChargingStateEnumType, §3.23 ConnectorStatusEnumType; accessed 2026-10-22.

Talk to us about your chargers

What happens next

  1. Tell us about your network.
  2. Meet a Kinethra specialist.
  3. Get your chargers live on Kinethra.
  • 40,000+ chargers onlineOn the Kinethra platform.
  • OCPP 1.6 and 2.0.1Kinethra works with OCPP chargers from any manufacturer.
  • No commission on charging revenueKinethra takes none.
  1. 01Contact
  2. 02Business
  3. 03Request

Step 1 of 3

We use your details to answer your request. See our Privacy Policy for details.